Datamax H-4606X Betreibershandbuch Seite 108
- Seite / 186
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
98 H-Class
Cotton Swab Procedure (for users of direct thermal media, or thermal transfer media
with wax ribbon):
A. Perform the Preliminary Cleaning Steps, as described above.
B. Turn OFF the power switch and unplug the printer. Using a Cotton Swab moistened (not
soaked) with isopropyl alcohol, gently clean the printhead surface of all build-up.
C. Allow the printhead to dry. Reinstall media (and ribbon, if necessary). Plug in the printer
and turn ON the power switch. Run a few sample labels and examine them. If streaking
is still present, go to "Cleaning Card Procedure" below; otherwise, this completes
cleaning.
Cleaning Card Procedure (for users of direct thermal media, or thermal transfer media
with wax/resin ribbon combinations; also for unsuccessful Cotton Swab cleaning attempts):
A. Perform the Preliminary Cleaning Steps, as described above.
B. Place a Cleaning Card under the printhead. (Part number 70-2013-01 for 4-inch cards;
and, 70-2013-01 for 6-inch cards)
C. Close and lock the Printhead Latch and disengage the Leveling Cam.
D. Close the cover then press and hold the TEST Button to initiate cleaning. (As an
alternate, enter the menu system and select CLEAN HEAD NOW see Section 4.2.1.)
E. After the cleaning card has been run through the printer, reinstall media (and ribbon, if
necessary). Plug in and turn ON the printer. Run a few sample labels and examine them.
If streaking is still present, go to Cleaning Film Procedure (below); otherwise, this
completes cleaning.
Cleaning Film Procedure (for users of thermal transfer media and resin ribbon,
operating with a Heat Value of 22 or higher, or when all previous cleaning methods prove
unsuccessful):
A. Perform the "Preliminary Cleaning Steps", as described above.
B. Place a sheet of Cleaning Film under the printhead. (Part number 70-2087-01 for 4-inch
film; and, 70-2087-02 for 6-inch film)
C. Close and lock the Printhead Latch and disengage the Leveling Cam.
D. Close the cover then press and hold the TEST Button to initiate cleaning. (As an
alternate, enter the menu system and select CLEAN HEAD NOW see Section 4.2.1.)
- Operator’s Manual 1
- Copyright Information 3
- Listed 4
- Special Instructions 6
- Contents 7
- Overview 11
- 1.1.1 Standard Features 12
- (available except as noted) 13
- Option Installation 15
- Getting Started 17
- 2.2 Installation 18
- Setting up the Printer 23
- 3.1.3 Rewinding Media 29
- 34
- 3.2 Media Sensor Adjustment 35
- 3.3 Ribbon Loading 36
- 3.4 Quick Calibration 39
- 30 H-Class 40
- Using the Control Panel 41
- 4.2 The Menu System 43
- 4.2.1 Media Settings 45
- Section 7 for label details 48
- 4.2.3 Printer Options 50
- 4.2.4 System Settings 61
- • DPL SOP Emulation; and 66
- • DPL Label Store 66
- 4.2.5 Communications 70
- NETWORK REPORT 73
- 4.2.6 Diagnostics 77
- 4.2.7 MCL Options 80
- 4.3 The Test Menu 81
- 4.3.2 Ribbon Test Label 82
- 4.3.3 Test Label 82
- 4.3.4 Validation Label 82
- 4.3.5 Print Configuration 83
- 4.3.6 Print Last Label 83
- 4.3.7 User-Defined Label 83
- 74 H-Class 84
- Operating, Adjusting and 85
- Maintaining the Printer 85
- If changes require a 87
- 5.2 Calibration 88
- Do not position the 91
- Sample Calibration Table 92
- • Die-cut – Remove a label 93
- • Notched – Position the 93
- The re-sampled 95
- If the calibration 97
- 5.3 Reset Methods 98
- 5.6 Maintenance 102
- Schedule 103
- Preliminary Cleaning Steps 107
- 5.7 Updating the Firmware 110
- If UNCALIBRATED is 112
- 5.9 Downloading Fonts 113
- Downloaded Font Removal 114
- Troubleshooting 115
- To continue printing, enter 123
- When the SENSOR 125
- 6.3 Hex Dump Mode 126
- Specifications 127
- H-6212X & H-6310X Models 134
- Media (continued) 138
- 7.4 Print Quality Controls 140
- Appendix A 141
- File Handling Messages 142
- 134 H-Class 144
- Appendix B 145
- Speed Ranges 146
- 138 H-Class 148
- Appendix C 149
- Appendix D 151
- Appendix E 155
- 146 H-Class 156
- Appendix F 157
- Appendix G 159
- 156 H-Class 166
- Appendix H 167
- Warranty Information 181
- General Warranty Provisions 182
- Limitation of Liability 182
- Glossary 183
- 176 H-Class 186
Verwandte Produkte und Handbücher für Etikettendrucker Datamax H-4606X
(20 Seiten)
(4 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern